ATTO Technology 2370E Bedienungsanleitung

ATTO FibreBridgeInstallation and Operation ManualATTO FibreBridge 2370EATTO FibreBridge 2390C/R/D ATTO FibreBridge 2400C/R/D

5ATTO Technology Inc. FibreBridge Installation and Operation Manual 1.2 ATTO FibreBridge 2390R/DThe ATTO FibreBridge 2390R/D is a 4-Gigabit Fibre Cha

6Manual reset switchA manual reset switch reboots the FibreBridge.To reset the FibreBridge, depress the reset button for no more than three seconds. T

7ATTO Technology Inc. FibreBridge Installation and Operation Manual 1.3 ATTO FibreBridge 2390CThe ATTO FibreBridge 2390C is a 4-Gigabit Fibre Channel

8Embedded in the Ethernet port connector: a lighted green LED shows a valid link; off indicates that no link is present. A separate blinking yellow LE

9ATTO Technology Inc. FibreBridge Installation and Operation Manual 1.4 ATTO FibreBridge 2400R/DThe ATTO FibreBridge 2400R/D is a high performance br

10Manual reset switchA manual reset switch reboots the FibreBridge.To reset the FibreBridge, depress the reset button for no more than three seconds.

11ATTO Technology Inc. FibreBridge Installation and Operation Manual 1.5 ATTO FibreBridge 2400CThe ATTO FibreBridge 2400C is a high performance bridg

12Exhibit 1.5-1 FibreBridge 2400C bracket detail and board layoutReady/Fault LEDEthernet portFibre Channel portsSCSI portsSCSI activity LEDsFC activi

13ATTO Technology Inc. FibreBridge Installation and Operation Manual 2.0 Install the FibreBridgeIf you have not already completed the instructions on

14 If you do not have a DHCP server, get an IP address and subnet mask from your network administrator, type it into the area provided, and click on

ATTO Technology, Inc.155 CrossPoint ParkwayAmherst, New York 14068 USAwww.attotech.comTel (716) 691-1999Fax (716) 691-9353 Sales support: sls@attotech

15ATTO Technology Inc. FibreBridge Installation and Operation Manual 3.0 Configure the FibreBridgeTo configure the ATTO FibreBridge, use ATTO Express

163 Enter the Administrator (Admin) password where indicated. 4 Enter appropriate information into the New Admin Password, Confirm New Admin Password

17ATTO Technology Inc. FibreBridge Installation and Operation Manual 3.1 Map devicesAfter getting an IP address and entering ATTO ExpressNAV, you mus

18Mapping devices automatically1 If you are not already in the ExpressNAV interface, type the IP address of your FibreBridge in a standard browser as

19ATTO Technology Inc. FibreBridge Installation and Operation Manual 3.2 Remote monitoring, managementThe Ethernet port provides monitoring and manag

20SNMP-based monitoringThe Simple Network Management Protocol (SNMP) facilitates the exchange of management information between network devices. An ag

21ATTO Technology Inc. FibreBridge Installation and Operation ManualEmail messages provide error notificationEmail notification allows the FibreBridge

22Exhibit 3.0-5 The Email messages sent by the FibreBridge follow this format.Subject: [The Type of Event that Occurred] Message Body:This is a statu

23ATTO Technology Inc. FibreBridge Installation and Operation Manual 4.0 Update firmwareThe ATTO FibreBridge has several processors which control the

246 In the Send File box, enter the current FibreBridge .ima file or click the browse button to find it.7 Click Send File8 The FibreBridge acknowledge

Contents 1.0 ATTO FibreBridge provides storage options ...1ATTO FibreBridge 2370E features, benefitsATTO FibreBridge 2390

25ATTO Technology Inc. FibreBridge Installation and Operation Manual 5.0 Interface optionsAlternative methods to the ATTO ExpressNAV interface may be

26• Flow Control: None• Terminal type: ASCII• Echo: on f. Click OK.4 After you connect to the Fibre Bridge, start-up messages are displayed. These

i ATTO Technology Inc. FibreBridge Installation and Operation ManualAppendix A CablingATTO FibreBridge SCSI ports connect SCSI storage devices into

iiAppendix B CLI provides ASCII-based interfaceThe command line interface (CLI) provides access to the ATTO FibreBridge Services through a set of AS

iii ATTO Technology Inc. FibreBridge Installation and Operation ManualCLI error messagesThe following error messages may be returned by the Command li

ivEthernetSpeed auto set ethernetspeed 100EventLog enabled set eventlog disabledEventLogFilter all all all set eventlogfilter gen info enabledExit exi

v ATTO Technology Inc. FibreBridge Installation and Operation ManualSCSIDomainValidation scsidomainvalidationSCSIInitId 0x07 set scsiinitid 2 12SCSIPo

viCommand explanationsAutoLogSenseControls whether current data from log pages in a SCSI target device is available automatically.Default: disabledset

vii ATTO Technology Inc. FibreBridge Installation and Operation ManualDisplayEventLog Displays the event log. The event log may be filtered using the

viiiEmailNotifyAddressConfigures notification addresses. Index is a number 1-5. Full Email address is a fully qualified Internet Email address, not mo

2.0 Installing the FibreBridge ...13Unpack the packing box; verify contentsInstall the F

ix ATTO Technology Inc. FibreBridge Installation and Operation ManualFCHardRegulates FC hard address assignment. Under soft addressing, the FibreBridg

xFirmwareRestartCauses the FibreBridge to reboot, then re-initialize its firmware.Use the forced option to override any CLI reservation held by other

xi ATTO Technology Inc. FibreBridge Installation and Operation ManualMinOpTemp (FB2390, FB2400 only)Regulates/displays the minimum enclosure temperatu

xiiRouteAssigns a Fibre Channel address to a target destination device. If you try to map a new SCSI BTL to the same FC LUN, the new BTL overwrites th

xiii ATTO Technology Inc. FibreBridge Installation and Operation ManualSCSIPortTerminationConfigures/reports the SCSI internal termination of the SCSI

xivSNMPTrapAddressSets/displays the IP trap addresses and levels.Consult your network administrator for further assistance with SNMP.Index: value betw

xv ATTO Technology Inc. FibreBridge Installation and Operation ManualTimeZoneControls/displays the time zone if SNTP is disabled. Setting may be EST,

xvizModemAllows transfer of a firmware image to or from the FibreBridge using the zModem file transfer protocol. Available only through the RS232 inte

xvii ATTO Technology Inc. FibreBridge Installation and Operation ManualAppendix C Standards and compliancesThe equipment described in this manual ge

xviiiIn addition the FibreBridge 2370E conforms to EN55024.This Declaration will only be valid when this product is used in conjunction with other CE

Appendix D Warranty information ...xixManufacturer limited warranty

xix ATTO Technology Inc. FibreBridge Installation and Operation ManualAppendix D Warranty informationManufacturer limited warrantyManufacturer warra

xx

1ATTO Technology Inc. FibreBridge Installation and Operation Manual 1.0 ATTO FibreBridge provides storage optionsThe ATTO FibreBridge™ family of prod

2ATTO FibreBridge 2390C/R/D features, benefitsThe ATTO FibreBridge 2390C/R/D is a 4-Gigabit Fibre Channel-to-SCSI bridge configured with a single 4-Gb

3ATTO Technology Inc. FibreBridge Installation and Operation Manual 1.1 ATTO FibreBridge 2370EThe ATTO FibreBridge 2370E is a 4-Gigabit Fibre Channel

4LED Header P5 Pins LED Header P6 PinsExhibit 1.1-1 FibreBridge 2370E board layout1 Ready LED Cathode2VDD 3.33 Power OK LED Cathode4VDD 3.35 Fault LE